Page 444 - Tires 2017

DRAG/V-TWIN TOOLS

STREET XL SPROCKET NUT SOCKET TOOL
TIRES FOR 91‑17 XL AND BUELL MODELS
(EXCEPT BUELL 1125R)
SPROCKET SHAFT BEARING •Short socket is specifically designed to remove, install
NUT WRENCH and properly tighten the front final drive sprocket/ pulley
DRAG/ FOR 55‑68 BIG TWIN •Short socket ensures the mainshaft on the XL extends through the guidance
collar for correct alignment
V-TWIN TIRES •Used to install and remove bearing nut •Provides full contact to the nut when tightening
DESCRIPTION PART # DESCRIPTION PART #
Sprocket shaft bearing nut wrench DS‑196168 XL sprocket nut socket 3802‑0066

SCOOTER
TIRES

DS‑196042
SPROCKET SHAFT
OFFROAD DS‑196046 DS‑196045 PROTECTOR CAP
TIRES SPROCKET SHAFT BEARING RACE TOOL FOR 55‑06 BIG TWIN

®
•Used to remove and install Timken bearing race on motor cases •Protects sprocket shaft when using crank
•Use drivers with handle PART #DS‑196042 assembly removing tool PART #DS‑196089 or
ATV/UTV DESCRIPTION PART # DESCRIPTION PART # a press
TIRES & BEARING RACE TOOL DRIVER HANDLE DESCRIPTION PART #
WHEELS For 96‑02 Big Twin DS‑196046 Handle/ driver only (ea.) DS‑196042 Sprocket shaft protector cap DS‑198637

For 86‑03 XL, 94‑02 Buell
DS‑196045

TUBES &
ACCESSORIES
BEARING AND RACE PULLER TOOL
•Multi‑faceted tool has many uses
SHOP EQUIPMENT •Removes flywheel sprocket shaft inner bearing race on 03‑07 Twin Cam
& STANDS •Can be used to remove Timken bearing (OEM #9028 or #9029) on
55‑07 Big Twins, including JIMS 120” engines
•Can be used to remove Timken bearing pinion shaft inner bearing race on
57‑07 XL, including all Buells
GENERAL, •Can also be used to remove press‑fit transmission gears and bearings from DESCRIPTION PART #
METRIC SERVICE/ input and output shafts on all 02‑07 V‑Rod models Bearing and race puller tool 3801‑0088

MAINTENANCE
TOOLS

DRAG/
V-TWIN TOOLS ENGINE ROTATOR 3801‑0099
•Rotates flywheel/ piston assembly with engine still in CRANKSHAFT
frame or on a bench
•The perfect tool when doing pushrod adjustments, building big‑inch 3801‑0100 BEARING TOOL
engines and checking operating clearances
CHEMICALS & •Also can be used to keep the flywheel assembly from rotating when •Used to remove and install the right crankcase
bearing in Twin Cam motors
LUBRICANTS torquing the cam drive sprockets retention bolts •Allows straight installation, without damage to
1
•Built with a long socket design, making it easier to use without a /2” drive extension on your /2” driver the case
1
NOTE: Not for use with an air or electric impact wrench; this tool is only guaranteed for use with hand drivers. •Comes with instructions
DESCRIPTION PART # DESCRIPTION PART # DESCRIPTION PART #
CLEANERS, For all 07‑17 Twin Cam, 06 Dyna Glide 3801‑0099 For 55‑06 Big Twin (except 06 Dyna Glide) 3801‑0100 Crankshaft bearing tool DS‑196194
POLISHES &
PAINTS
TRANSPORT
& TRAILER
CRANKSHAFT BEARING
ENDPLAY SETUP TOOL RATCHETING
•For Big Twin engines to set up crankshaft CRANKSHAFT WRENCHES
MERCHANDISING bearing endplay •To rotate the crankshaft during engine timing COMPENSATOR BOLT
•Diameter of the bolt is turned slightly smaller and clearance checks
®
than the actual crankshaft diameter, allowing •Offset design so it will not interfere with the TORX SOCKET
the inner bearing races to be installed and motor case FOR 14‑17 BIG TWIN MODELS
removed without pressing them on or off •Chrome‑plated with EZ Grip screwdriver‑style
•Allows much faster changing of shims and faster handle for comfort and more turning power •Correct style driver/ socket for the
INDEX setup time PART # DESCRIPTION compensating sprocket retaining fastener
PART # DESCRIPTION 3801‑0207 For 07‑17 Twin Cam, 06 Dyna; 24‑spline DESCRIPTION PART #
3801‑0196 For Big Twin engines (except M‑Eight) 3801‑0200 For 55‑06 Big Twin (except 06 Dyna); 10‑spline Compensator bolt Torx ® socket 3802‑0070
444 All part numbers in BOLD MAGENTA are new this year.